I got this as a gift (I had questioned for a screen protector because I figured it would be a excellent thought to protect the screen on my tablet PC since it gets handled so much.). Too bone idle to cut it to size (I have a 14.1″ 15:9 screen) and place it on, it sat in my room for a year or two until I finally chose to try it.
Cold it worked out fine (I used a ruler and craft knife on a cold board, carefully), but after that the problems ongoing. The instructions are very unclear and confusing, but I was eventually capable to figure out what to do. The packets of cleaning solution were dried up, which I had thought might be due to the length of time it sat in my room, but I see others have had the same problem. I wiped the screen down, using a modest water in house of the solution, and found that the included cloths leave tiny fibers behind, so I had to work more to get rid of those.
After I finally got my screen clean, I set out to apply the film. I had it most of the way on when I noticed a tiny spec of dust or something had made a bubble. I peeled the film in trade and indifferent the spec, but as I did so, more and more tiny debris accumulated on the underside of the film due to the static cling, and it proved to be impossible to protect clean.
With a screen littered on one side with unsightly bubbles (you can scrape the bubbles out single if here’s nothing solid in them), I peeled the film off and threw it out. $20 and all this effort for two months of fizzing protection? No thanks.
Not single is this way over-priced for the merchandise, it is impossible to install without getting impossible-to-remove air bubbles causes by the dust specs that are attracted to the screen protector as you try to install. I tried for an hour, gave up, ripped it off, and threw it away. Don’t get burned!
I reckon that the other reviews have already made it cleaar that it is hard to apply this product without getting air bubbles. After a few tries you will start to collect particals on the film that make it impossible to get rid of the bubbles in the film (these are the bubbles that do not go no matter how many time you rub them with the applicator stick). I found that you can remove particals by lifting them off with scotch tape.
{ 5 comments… read them below or add one }
This item has been on my laptop for a year now, and it is still perfect.
It made the screen stop reflecting light from behind me, and a monkey may possibly place it on.
Straightforward to clean, but you would have to be eating hot-wings and upset the screen with your greasy
fingers to place a smudge on it. (Question my son how I know that) lol
Wipe it off with some Windex or screen anti-static cleaner and its excellent until something stupid happens again.
It has not bubbled, scratched, or be converted into trying to read through like protectors I have used in the past.
I got this as a gift (I had questioned for a screen protector because I figured it would be a excellent thought to protect the screen on my tablet PC since it gets handled so much.). Too bone idle to cut it to size (I have a 14.1″ 15:9 screen) and place it on, it sat in my room for a year or two until I finally chose to try it.
Cold it worked out fine (I used a ruler and craft knife on a cold board, carefully), but after that the problems ongoing. The instructions are very unclear and confusing, but I was eventually capable to figure out what to do. The packets of cleaning solution were dried up, which I had thought might be due to the length of time it sat in my room, but I see others have had the same problem. I wiped the screen down, using a modest water in house of the solution, and found that the included cloths leave tiny fibers behind, so I had to work more to get rid of those.
After I finally got my screen clean, I set out to apply the film. I had it most of the way on when I noticed a tiny spec of dust or something had made a bubble. I peeled the film in trade and indifferent the spec, but as I did so, more and more tiny debris accumulated on the underside of the film due to the static cling, and it proved to be impossible to protect clean.
With a screen littered on one side with unsightly bubbles (you can scrape the bubbles out single if here’s nothing solid in them), I peeled the film off and threw it out. $20 and all this effort for two months of fizzing protection? No thanks.
Not single is this way over-priced for the merchandise, it is impossible to install without getting impossible-to-remove air bubbles causes by the dust specs that are attracted to the screen protector as you try to install. I tried for an hour, gave up, ripped it off, and threw it away. Don’t get burned!
IT’S O.K. BUT NOT WHAT I EXSPECTED. IT MAKES THE SCREEN LOOK DIM AND DISTORTED..OH,WELL
I reckon that the other reviews have already made it cleaar that it is hard to apply this product without getting air bubbles. After a few tries you will start to collect particals on the film that make it impossible to get rid of the bubbles in the film (these are the bubbles that do not go no matter how many time you rub them with the applicator stick). I found that you can remove particals by lifting them off with scotch tape.